tearout
Jump to navigation
Jump to search
English[edit]
Etymology[edit]
Noun[edit]
tearout (plural tearouts)
- (carpentry, woodworking) Synonym of blowout.
- 1949, E. M. Davis, “Shaping the End Grain of Redwood for Core Stock”, in United States Department of Agriculture Forest Service, editor, Reports, page 11:
- The heartwood gave consistently better results than the sapwood, in fact nearly all the tearouts and most of the rough cutting were found in the sapwood.
- 2002, Gary Rogowski, The Complete Illustrated Guide to Joinery, page 21:
- Tearout can also occur below the final depth of cut.
- 2005, Working with Tablesaws, page 48:
- This slot is a hot zone for tearout because it creates an unsupported surface for the material being cut.
- He's got a bunch of tearouts on the finished side. It's cheaper and easier to redo it than to patch it, but the job's unprofitable either way.
- (structural engineering) The shearing of metal by a bolt, pin, rivet, or similar fastener due to stress.
- 1944, Joseph Albert Ashkouti, Alexander Klemin, Aircraft Mechanic's Pocket Manual, pages 11-16:
- The tearout load is determined by the formula Pe - 2AFx
- 2007, John H. Bickford, Introduction to the Design and Behavior of Bolted Joints:
- Note that computation of tearout strength becomes far more complicated if there are several rows of bolts on each side of the joint.
- 2012, Federico Mazzolani, Ricardo Herrera, Behaviour of Steel Structures in Seismic Areas:
- The block tearout (Figure 8) and net section fracture (Figure 9) of the brace failure modes in most cases have predicted values that are similar, which helps to explain why braces predicted to faile with block tearout of the brace frequently failed with net section facture of the brace.
- 2019, Alphose Zingoni, Advances in Engineering Materials, Structures and Systems, page 1309:
- Equation 1 and 2 are established to predict the ultimate bearing resistance of tearout failure and splitting failure, which shows satisfactory agreement with test results in Figure 9.
- (medicine) The tearing of tissue at the position of an incision, suture, staple, pin, etc.
- 2012, Volker Schumpelick, Andrew N Kingsnorth, Incisional Hernia:
- When testing the suture tearout force, Tauber and Seidel found that the tearout force was one third to one fourth of normal tissue.
- 2012, Urs Heim, Karl M. Pfeiffer, Internal Fixation of Small Fractures, page 34:
- The resistance of screws to tearout forces depends chiefly on the screw diameter ( and bone strength ) and on the length of screw thread gripping the bone (cortical thickness).
- 2022, Myron Yanoff, Jay S. Duker, Ophthalmology, page 354:
- Backward traction on the capsular flap forms the basis of a predictable technique for rescuing the capsulorrhexis from a radial tearout.
- The demolition phase of remodeling or decommissioning.
- The plan is to have the tearout done by next week.
- 1992 November-December, Christopher Phillips, “Demolition”, in Old-House Journal, volume 20, number 6, page 30:
- Lay a window fan down on top of the chimney during tearout. It will pull out 90% of the fine dust that would otherwise permeate every inch of the house — plus, you don't have to breathe it.
- 2005, Michael W. Litchfield, Renovation, page 164:
- Remove and store them till you are done with tearout and rough framing.
- 2012, J.P. Bennett, K.-S. Kwong, “Industrial Applications for Spent Refractory Materials”, in S. K. Sundaram, Dane R. Spearing, John D. Vienna, editor, Environmental Issues and Waste Management Technologies in the Ceramic and Nuclear Industries VIII, page 5:
- Beneficiation of contaminated material makes up a high portion of refractory recycling costs, underscoring the importance of keeping the material clean on tearout.
- A card, page, or set of pages designed to be detached from a magazine or book, usually along a perforated line.
- 1971, Sherman Alan Stewart, A Glossary of Urethane Industry Terms, page viii:
- In the back of the book there are tearout sheets that can be used to give additional data to the publishers for the correction or expansion of this book.
- 1978, United States. Department of the Army, Material Supplyman: MOS 76D Skill Levels 1 and 2, pages 1-7:
- You may also use this tearout sheet to order QMS materials referred to in the manual .
- 1996, The Compleat Lawyer - Volume 13, page 20:
- This issue's tearout is about how long your clients should keep federal income tax return records.
- 2012, Ben Conry, 31 Days Before Your CompTIA A+ Exams, page xxvii:
- Also, before you take the Essentials and Practical Application exams, use the checklists on the back of the tearout to ensure you have a firm grasp of the exam topics.
- A subgenre of dubstep characterized by intense basslines, distorted synths, and high-energy rhythms.